Ruckus: Difference between revisions
Jump to navigation
Jump to search
No edit summary |
|||
| (5 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
=General= | =General= | ||
Firstly, David Ellis has a site with some very useful Brocade/Ruckus ICX guides, tips, etc: http://www.netadmin.us/icx.htm | |||
===Show Management IP=== | |||
sh ip | |||
===Show List of Interfaces=== | |||
sh int brief | |||
===Show Interface DOM Info=== | |||
First, ensure optical-monitoring is enabled: | |||
(config)# optical-monitor 1 | |||
After a while, you should be able to see DOM info, if the optic supports it: | |||
sh optic 1/3/1 | |||
===Determine port of MAC=== | ===Determine port of MAC=== | ||
sh mac-address | inc 5916 | |||
Output: | Output: | ||
3817.c3ca.5916 11 Dynamic 277 | |||
===Show detailed LLDP=== | ===Show detailed LLDP=== | ||
sh lldp neigh detail ports e 11 | |||
Output: | Output: | ||
| Line 33: | Line 53: | ||
===Span/Mirror Port=== | ===Span/Mirror Port=== | ||
; MIRROR Port: the port | ; MIRROR Port: the port in which Wireshark is connected (e.g., 1/1/5 below) | ||
; MONITOR Port: the port you want to capture traffic from (e.g., 1/1/3 below) | ; MONITOR Port: the port you want to capture traffic from (e.g., 1/1/3 below) | ||
(config)# mirror-port ethernet 1/1/5 | |||
(config)# interface e 1/1/3 | |||
(config-if-e1000-1/1/3)# monitor ethernet 1/1/5 both | |||
=Security= | =Security= | ||
2020-06-07 - Some good info to hold you over: http://www.netadmin.us/docs/TACACS-RADIUS.pdf | 2020-06-07 - Some good info to hold you over: http://www.netadmin.us/docs/TACACS-RADIUS.pdf | ||
Latest revision as of 19:23, 17 February 2024
General
Firstly, David Ellis has a site with some very useful Brocade/Ruckus ICX guides, tips, etc: http://www.netadmin.us/icx.htm
Show Management IP
sh ip
Show List of Interfaces
sh int brief
Show Interface DOM Info
First, ensure optical-monitoring is enabled:
(config)# optical-monitor 1
After a while, you should be able to see DOM info, if the optic supports it:
sh optic 1/3/1
Determine port of MAC
sh mac-address | inc 5916
Output:
3817.c3ca.5916 11 Dynamic 277
Show detailed LLDP
sh lldp neigh detail ports e 11
Output:
Local port: 11
Neighbor: 78a6.e109.ddd1, TTL 114 seconds
+ Chassis ID (MAC address): 78a6.e109.dda0
+ Port ID (MAC address): 78a6.e109.ddd1
+ Time to live: 120 seconds
+ System name : "s1-137-switch"
+ Port description : "10GigabitEthernet1/2/1"
+ System capabilities : bridge
Enabled capabilities: bridge
+ 802.3 MAC/PHY : auto-negotiation supported, but disabled
Operational MAU type : 1000BaseSX-FD
+ Link aggregation: not capable
+ Maximum frame size: 10200 octets
+ Port VLAN ID: none
+ Management address (IPv4): 10.0.0.29
Span/Mirror Port
- MIRROR Port
- the port in which Wireshark is connected (e.g., 1/1/5 below)
- MONITOR Port
- the port you want to capture traffic from (e.g., 1/1/3 below)
(config)# mirror-port ethernet 1/1/5 (config)# interface e 1/1/3 (config-if-e1000-1/1/3)# monitor ethernet 1/1/5 both
Security
2020-06-07 - Some good info to hold you over: http://www.netadmin.us/docs/TACACS-RADIUS.pdf